clocd_imageThe local UPS driver and I are on a first name basis. I regularly get all kinds of audio gear sent to me for evaluation and testing from companies all over the world. And some of these cartons are really big, and really heavy. But a few days ago, a tiny little package arrived at the lab and knowing I had not ordered a pack of gum via UPS, I was mystified to find out what was inside. I cut the box open, and inside I found a product from a whole new company, called Caché. The Caché brand of audio equipment is a line of signal processors, converters, line drivers and bass restoration products. Specializing in 12 volt applications only, the product line consists of a half dozen pieces of gear designed to assist in OEM interfacing and system control and tuning.

To find out more about this new brand, and what they were all about, I spoke to the company’s president, Mike Morris, about the Caché products, and he told me, “We recognized the real need for products that exist to help dealers interface today’s aftermarket audio products with modern OEM sources, and to provide tuning ability and superior audio performance. For several years, we looked at the best the industry had to offer, talked to hundreds of dealers and installers, and then set out to build products with higher performance but at very competitive prices.”

The product they sent me to check out is their CLOC+D high level to RCA converter and line driver. Measuring only 3.5 inches square (including connectors) and about an inch high, the CLOC+D will easily fit into any tight space you might want to put it in. Very nicely finished with a black powdercoated housing and a CNC machined, brushed aluminum top cover, and with heavy-duty nickel plated panel mounted RCA outputs it gives the impression of being a high end product. The CLOC+D (Caché Line Output Converter+Driver) is designed to accept the high level (speaker) output of any OEM source unit or amplifier, and provide a high performance RCA level output signal. Or, it can also be used to simply convert a mediocre RCA signal to a truly high performance one. If you have an aftermarket source unit with low output voltage, and/or questionable source impedance, the line driver capability of the CLOC+D will transform that signal into something much superior.

Turn-on can be accomplished two ways, either by a traditional 12V trigger wire, or it has signal sense turn on capability for source units without a “trigger” lead. A separate 12V remote output connection is there to provide the trigger voltage required to turn on aftermarket amplifiers. The remote output function operates regardless of which method is used to turn on the CLOC+D.

The power and signal input connections are accomplished via a pair of quick disconnect multi-wire connectors. You insert the wires, tighten down the (tiny) screws, and then slide the connector in place. Controls are few and simple. There is a switch on the top of the unit to select either the high level inputs or the RCA inputs, and there is a gain pot mounted between the quick disconnect terminals to adjust the amount of available gain. A yellow “Maximum” LED will illuminate to indicate the onset of clipping, and a red Power LED lets you know the unit is turned on and passing signal.

I connected the CLOC+D to the speaker outputs of a radio on my test bench, and it turned on with the input signal very quickly, in less than a second. This quick turn on is a good thing, because it allows a stable signal to already be at the amplifiers inputs before it turns on, as most amplifiers have a few seconds of delay to prevent turn on pop noises. As the owner’s manual stated, the high level inputs will accept input signals up to 100 watts per channel. After playing with it for a few minutes, you know I took it apart. I was surprised to see the circuit density it has. (see photo) There are dozens of tiny very low tolerance surface mount devices inside, on a double sided fiberglass PCB. I connected it to my trusty Audio Precision analyzer to get the real numbers out of it, and see just how good it really was.

As it turned out, it’s pretty damn good. Using a balanced signal on the high level inputs, the CLOC+D delivered a maximum RCA output voltage of 10.4 volts, with a very low output impedance of 28 ohms. The RCA inputs will accept over 9 volts of signal without clipping, so the Caché piece is going to be compatible with any source unit or preamp. I measured the frequency response to be very flat as well, within 0.5dB from 20Hz to 20kHz. Signal to Noise measured better than -90dBA, and stereo separation was also excellent at better than -65dB. The voltage out of the remote output terminal did not drop much when compared to the supply voltage, (within 5%) which is important for amplifiers that need at least 11 volts to turn on.




Free Promotion on Work Varianza & Schwert Series Wheels

WORK Wheels USA has announced a free promotion on any WORK Varianza or Schwert series wheel purchases made until 11/3/10.  Purchase a set of (4) wheels and choose from one of the following 3 FREE…
Read More

Yokohama Announces Six New ADVAN Tire Sizes

FULLERTON, CA (Sept. 20, 2010) - Yokohama Tire Corporation has added six sizes to its ultra high-performance (UHP) ADVANR line: three each for the NeovaR AD08 and S.4R. The latest AD08 sizes are 245/40R19 94W,…
Read More

Royal Purple Announces 2012 Show It Off at SEMA Contest

High Performance synthetic lubricant manufacturer Royal Purple announced today the return of its Show It Off at SEMA contest. Beginning July 2 and running through the month of July, the contest offers entrants a chance…
Read More