Want to see where the trend in car modifications is going? Well, look no further than this Team Hybrid EVO 9. The mission statement behind this build was simple: make a sick looking Evo that could hold its own at shows and still be a street car. This is no trailer queen, but rather a daily driver that throws down over 500awhp on pump gas! As with any daily it has all of the luxuries and gadgetry onboard as well as a fully appointed interior.
Tuners that understand how to maximize E85 have great gains and at 505awhp and 481lb-ft of twist, this Evo is no exception.
Owner Charleston Penesa of Las Vegas, NV realized that to have the functionality of a sedan with outrageous street-able power, he didn’t have to look further than the Evo. Well known for outgunning exotics on the circuit, the Evo is an ideal mod choice and with that, Penesa stepped it up. The 4G63 motor was pulled and filled with new gear including BC pistons, rods and crankshaft. The head was ported, polished and filled with a completed BC valvetrain and a pair of 280º cams. Penesa sided with a 3076R turbo kit from long-time Mitsubishi specialist Buschur Racing. Air is hauled in using and HKS super suction intake and chilled with an HKS front mount connected up with RMR piping and vented by a Forge BOV. Post-combustion, the gases head into an HKS downpipe, Ultimate Racing test pipe and an HKS Carbon Titanium exhaust.
Using a flashed EVO IX PCM, the results were impressive. The fuel system has been set up to use E85 ethanol available at many pumps, which burns much cooler than conventional gas. Tuners that understand how to maximize E85 have great gains and at 505awhp and 481lb-ft of twist, this Evo is no exception. All that extra jam meant that Mitsubishi OEM clutch would tap out and therefore had to be replaced. A SPEC Super Twin Disc clutch was added, but the balance is all Mitsu!
While the Evo is blessed with unreal natural abilities, there is always room for upgrades. Penesa started with a set of Endura-Tech 10-way adjustable coilover suspension using 7kg and 5kg springs. A pair of Cusco sway bars was added to the project along with GReddy strut bars to brace the chassis. The factory rubber bushings were all pressed out and replaced with Energy Suspension polyurethane bushings.
All of the suspension mods benefited from the amount of rubber Penesa added and the reduction in rotating mass. He sourced a set of Rays Gram Lights in 18x10-inches with a sizable +15 offset. The lightweight forged alloys were wrapped in a set of BFGoodrich R1 tires measuring 275/35R18. Lurking behind the white spokes are Rotora 6-piston front calipers with 355mm rotors up front and 4-piston rear calipers with 330mm rotors in the rear. Rotora carbon compound racing pads were fit
ted to all four corners and the Rotora stainless steel brake lines were filled with Amsoil Synthetic brake fluid.
Since the car still is pulled off the road every other weekend to attend shows, it had to look the part. Penesa installed an APR Performance EVIL-R wide body kit along with an APR front diffuser and drenched the project in several coats of Tangelo Pearl. A Seibon carbon fiber hood and trunk were added along with a Carbon8 full carbon fiber roof panel. The final touches were some JDM Evo7 headlights and taillights along with some RalliART carbon fiber mirrors.
Inside the cabin, the upgrades just kept coming. Penesa added a pair of Bride Vios Low Max seats draped with Race Tech 4-point harnesses. Several interior panels were recovered in rich, red suede to highlight the interior. The occupants are surrounded by a Cusco 6-point roll cage finished in a ‘Takata Green’ paint job. Steering inputs are made with a Nardi 350mm deep corn steering wheel with and NRG 3.0 quick-release connected to an NRG short hub.
Read on for Full Specs