As many of you are aware of the more equipment and upgrades you have in your vehicle the less space you have to fit it all in. Especially when most of the vehicles come from the factory with very little room to begin with. In this article we will be eliminating some of the clutter by building two pods that will hold a total of three gauges apiece for our very own PAS Magazine HIN demo car, a Scion xD that the audio experts at Installer Institute built this year for the cross country HIN tour.

The Scion was delivered to us with a total of 9 gauges of which only six really needed to be used and in car show vehicle of this caliber we were going to need all the space we could get.

Step 1

The first step was to pull a mold of the area the gauges were going to be located in. We decided to locate three of the gauges directly above the factory gauge cluster and the other three above the radio. This required the tape and foil the entire top of the dash along with the windshield and floor board. When working on any car you can’t be to careful.

 

2_opt 3_opt 4_opt

Step 2

Appliing fiberglass is the next step, the idea is to pull a model of the dashes contours so that when we mount the finished product to the dash it will fit perfectly. In this step we applied 4 layers of fiberglass mat.

5_opt 6_opt 7_opt

 

Step 3

While the glass is curing we started to take apart the gauges. The gauges came apart very easy, we had to remove the mounting bracket and trim off all of the extra tabs so that the gauges would fit together correctly. Once you remove the guts of the gauges make sure you keep them in a safe place so they do not get damaged.

8_opt 9_opt 10_opt

 

Step 4

With the fiberglass dry we removed all the tape and foil and placed the gauges in place to make sure that everything would look good before we started to fabricate the gauges on to the fiberglass. Once everything checked out and looked good we traced an outline of the gauge pod onto the fiberglass and cut it out.


11_opt 12_opt
13_opt 14_opt

Step 5

Next step was to secure the plastic gauge housings into place. Super glue was used to attach them to each other as well as the fiberglass base. The gauges were set at a small angle so that they would be in the site of the driver. With the gauge housings mounted to the base they were set back into the vehicle to make sure that everything look cosmetically appealing.

15_opt 16_opt
17_opt 18_opt

 

Step 6

Our next step was to form the shape of the gauge pod, for this we used 2 part expanding foam. Thick construction paper was used to build walls around the base of the gauge pod, this was so the foam could build up and not out.

Step 7

With the foam cured it was time to start shaping the pods. Once the pods were shaped they were placed back into the Scion to see how they look and how everything matched up.

 

Step 8

Next we fiberglassed the each pod applying 3 layers of fiberglass mat. Once the mat dried it was grinded and body filler was applied to fill in all of the imperfections. With the pods sanded with 80 grit sand paper they again were test fit to the vehicle and then prepped for wrapping.

Step 9

Now it is time to cover the gauge pods. The colors of the cars interior was a combination of black, gray and blue suede. We chose to cover the pods in blue suede so they would stand out and catch everyone eye as they walk by at the Hot Import Night shows. Once the pods were covered they we attached to the dash from the bottom and wired up.

32_opt

34_opt

 

Remember Knowledge is Power

Look for the Scion at all the HIN show this year. If you would like to build your skills as a mobile electronics installer and learn from the best fabricators in the industry log onto our web-site www.installerinstitute.com and see what the Installer Institute can do for you.

 

Installer Institute

1524 Ridgewood Ave.,

Holly Hill, FL, 32117

(800) 354-6782

www.installerinstitute.com

Remember doing it right the first time will always save time.

IF you have any questions or have any suggestions for future how-to article splease contact This e-mail address is being protected from spambots. You need JavaScript enabled to view it

 

Related Features

Vaughn Gittin Jr's 2015 Mustang RTR Spec 5 Concept

Story and Photography by Jordan Lenssen. The 2015 Mustang has been all the rage since being officially launched in September, 2014. The bolder lines, standard selectable drive modes, all-new 2.3-liter turbocharged inline-four and fully-independent rear suspension have made this the…
Read More

Unexpected Greatness: Joseph Bacigalupi's 2005 Subaru WRX Wagon

Written by Steven Loung / Photography by ICON Media When Joseph Bacigalupi got his 2005 Subaru WRX he had no intention of modifying it. While he convinced himself that the wagon would be good to get him and his wife…
Read More

Devil in a New Dress: Billy Vaughn's 1999 Nissan Silvia S15

Written by Eric Eikenberry / Photography by Eric Eikenberry Although you might not recognize it right away, this cool-looking, Army Green Silvia S15 is famous. In fact, we bet you’ve seen it before. Most people we know are at least…
Read More

The New BMW i8 Concept Spyder

BMW i presents the i8 Concept Spyder, the third debut from BMW’s future mobility sub-brand following the i3 Concept and the i8 Concept. The i8 Concept Spyder represents a vision of the future where intelligent thinking, advanced materials and innovative…
Read More

Backstage Pass: JL Audio

Company founder Lucio Proni (left), VP-Electronics Jeff Scoon (seated), with President Andy Oxenhorn (right). For almost as long as I’ve been in the industry, JL Audio has been a top manufacturer of subwoofer solutions for mobile audio enthusiasts. That’s well…
Read More